Superior Epoxies & Coatings, Inc. - Item # SG, Superior Grip
Superior Epoxies & Coatings, Inc. Superior Gloss Showroom Floor
Online Catalog Charts Spec Sheets Photo Gallery General Info News About Superior Contact Superior Reps Wanted Home
Construction Products
Dowel Bar Adhesives
•   Dowel Bar Adhesives
•   Patch Binders
•   Saw Cut Fillers
•   Crack Weld
•   Bumper Weld
   
Coatings & Floorings
Superior Gloss Safety Yellow Striping
•   Epoxy Primers
•   Glosses & Top Coats
•   Epoxy Seals
•   Binders
•   Surfacing Systems
   

Sealants
Dowel Bar Adhesives
•   Joint Seals
•   Security Sealant
   
 
 Search Catalog
      GO   
 All Categories    Superior Grip
All Categories > Coatings & Floorings > Superior Grip > Superior Grip > Item # SG  
Request Information

Item # SG Superior Grip



    Print Printable Page  
    Email Email This Page  
    Save To Favorites Save To Favorites
  

Superior_Grip

larger image
Superior Grip
100% Solids, Skid-Resistant, Safety Surfacing

SUPERIOR GRIP is a 100% solids, three component epoxy compound. SUPERIOR GRIP produces a highly skid-resistant surface with silicon carbide granules on dry and damp surfaces.
    Uses
    SUPERIOR GRIP is used on areas where slippery conditions exist such as ramps, stairs, walkways and docks. SUPERIOR GRIP may be used to protect floors against water, chemicals and heavy traffic.
    Advantages
  • 100% solids, no VOC.
  • Epoxy liquids are mixed in easy to use 1:1 by volume ratio.
  • Non-skid aggregate is extremely hard and skid resistant
  • Excellent water and chemical resistance.
  • May be applied to damp surfaces and under high humidity conditions.
    Surface Preparation
    Concrete Surfaces must be clean, sound, dry and free of all foreign materials such as oils, grease, loose paint, dust and laitance. This may be accomplished by sand blasting or scarifying, followed by an air blast to remove dust and debris from the application area.

    New concrete surfaces should be acid etched, rinsed thoroughly and allowed to dry.

    Steel Surfaces should be sand blasted to SSPC SP-10 near white. Water blast or mechanical abrading is an alternative method, as long as all rust, scale, paint and other foreign materials are removed. Steel must be coated the same day as cleaned.

    Wood Surfaces should be roughened by sanding.
    Mixing & Application
    1. Stir parts A & B
    2. Add contents of parts A & B to mixing bucket supplied.
    3. Mix thoroughly, being sure to scrape the sides and bottom with the mixing paddle supplied.
    4. Apply to floor immediately after mixing by pouring the mixed material over the surface and spreading it uniformly with a brush, roller, or notched trowel @ 100 square feet per unit. Mixed SUPERIOR GRIP has a working time of 30-45 minutes @ 75°F.
    5. Sprinkle silicon carbide granules evenly over the surface before coating starts to set (within 30 minutes)
    6. If less than unit quantity is to be applied, mix liquid components in a 1:1 ratio by volume and spread @ 100 square feet per gallon.
    Limitations
  • Do NOT apply when temperature is below 50°F.
  • Do NOT apply to latex modified mortar or concrete.
  • Do NOT place over working control joint.
    Clean Up
    Clean tools and equipment immediately with a suitable solvent such as xylene or lacquer thinner.
    Caution
    For professional use only. Epoxy systems can cause delayed dermatitis. Avoid prolonged contact with skin. See Material Safety Data Sheet for proper handling and required safety equipment.
    Specification
  • Packaging: 25 lb units covering 100 square feet
  • Mix Ratio by Volume: 1:1 by volume (liquids)
  • Color: Black
  • Pot Life (100 Grams): 30-45 minutes (neat)
  • Shelf Life: 2 Years
  • Coverage: 100 sq.
  • Cure Schedule: Initial Cure: 6-8 hours
  • Chemical Resistance: Excellent against water, most alkalies, and aliphatic hydrocarbons. Good against mild mineral acids. Fair against organic acids and methanol.
    Estimation Chart

    COVERAGE FOR COATING OR MEMBRANES
    Thickness of Coating Applied
    (1000 mils = 1 inch)    		 Coverage per U.S. Gallon
    100% Solids System
    1/4 inch = 250 mils 6.4 Square Feet
    3/16 inch = 187.5 8.5 Square Feet
    1/8 inch = 125mills 12.8 Square Feet
    100mils 16.0 Square Feet
    1/16 inch = 62.5 mils 25.5 Square Feet
    50 mils 32.0 Square Feet
    1/32 inch = 31.25 mils 51.0 Square Feet
    20 mils 80.0 Square Feet
    1/64 inch = 15.625 mils 102.0 Square Feet
    10 mils 160.0 Square Feet
    5 mils 320.0 Square Feet
    1 mil 1600.0 Square Feet
    If coating contains a solvent which will evaporate, thickness of coating will be reduced by same percentage as solvent loss.


Request Information
 

 

Superior Epoxies & Coatings, Inc. (800) 240-1310
Fax: (800) 240-7662
2527 Lantrac Court
Decatur GA 30035
© 2006 Superior Epoxies & Coatings. All Rights Reserved   
Web Design by SMF Associates