Superior Epoxies & Coatings, Inc. - Item # SN, Superior Novolac
Superior Epoxies & Coatings, Inc. Superior Gloss Showroom Floor
Online Catalog Charts Spec Sheets Photo Gallery General Info News About Superior Contact Superior Reps Wanted Home
Construction Products
Dowel Bar Adhesives
•   Dowel Bar Adhesives
•   Patch Binders
•   Saw Cut Fillers
•   Crack Weld
•   Bumper Weld
   
Coatings & Floorings
Superior Gloss Safety Yellow Striping
•   Epoxy Primers
•   Glosses & Top Coats
•   Epoxy Seals
•   Binders
•   Surfacing Systems
   

Sealants
Dowel Bar Adhesives
•   Joint Seals
•   Security Sealant
   
 
 Search Catalog
      GO   
 All Categories    Superior Novolac
All Categories > Coatings & Floorings > Superior Novolac Chemical Resistant Coating > Superior Novolac > Item # SN  
Request Information

Item # SN Superior Novolac



    Print Printable Page  
    Email Email This Page  
    Save To Favorites Save To Favorites
  

Superior_Novolac

larger image
Superior Novolac
100% Solids, Chemical Resistant, Epoxy Novolac Binder & Coating

SUPERIOR NOVOLAC is a unique, 100% solids epoxy system which exhibits superior resistance to acids, both mineral and organic, alkalies, salts, solvents, oils and other chemicals. SUPERIOR NOVOLAC is high gloss, abrasion resistant and moisture insensible. Coatings and toppings of SUPERIOR NOVOLAC have excellent resistance to thermal shock when subjected to frequent steam or hot water cleaning.
    Uses
    Chemical resistant coatings and/or binders for aggregate filled, trowel applied toppings. SUPERIOR NOVOLAC may be used as a protective top coating for other epoxy systems to provide improved surface chemical resistance in:

  • Chemical plants
  • Pulp & paper mills
  • Food processing plants
  • Dairies
  • Battery storage & charging areas
  • Plating plants
  • Waste treatment plants
    Advantages
  • Excellent chemical resistance
  • 100% solids, conforms to VOC regulations
  • High gloss, easily cleaned surface
  • Excellent bond to concrete, steel and wood
  • DOT Non-corrosive
  • Moisture insensitive
  • Easy to use 1:1 by volume mix ratio
    Surface Preparation
    Surface must be clean and free of any dust, oil, grease, laitance, curing compounds or any other contaminants. This should be achieved by sand blasting, water blasting or some other mechanical means. New concrete surfaces may be acid etched with muriatic acid and rinsed thoroughly. Surface may be dry or damp, but must be free of standing water.
    Mixing & Application
    Mix thoroughly, 1 part by volume of part A with 1 part by volume of part B, being sure to scrape the sides and bottom with a strong mixing stick or slow speed drill equipped with a paint propeller. Do not mix more than can be applied in 30 minutes. Apply mixed material by brush or roller. For best results, two coats should be applied. Allow the first coat to cure overnight. Apply the second coat within 24 hours.

    As a mortar, prime surface with neat epoxy. Prepare the mortar system by adding 2.5 to 3.5 gallons of clean dry sand to each gallon of mixed epoxy. Preferred types of sand are high grade silica sands such as Ottawa Flintshot, Mission, or their equivalents, Emery, or other forms of Alumina and Silicon Carbide. Blend the epoxy and sand until the sand is thoroughly wetted. Screed the mortar out onto the previously primed area, rake to distribute, then compact and trowel to finish. When used as a mortar, it is recommended that one or two topcoats be applied to seal the surface against chemicals and acids.
    Limitations
  • Do NOT apply when temperature is below 50°F.
  • Do NOT apply to latex modified mortar or concrete.
    Clean Up
    Clean tools and equipment immediately with a suitable solvent such as xylene or lacquer thinner.
    Caution
    For professional use only. Epoxy systems can cause delayed dermatitis. Avoid prolonged contact with skin. See Material Safety Data Sheet for proper handling and required safety equipment.
    Specification
  • Packaging: 2 gallon units;10 gallon units;110 gallon units
  • Mix Ratio by Volume: 1:1
  • Color: Clear, Gray, Red
  • Pot Life (100 Grams): 45-60 Minutes
  • Tensile Strength: 7600 psi (ASTM D-638)
  • Tensile Elongation: 6% (ASTM D-638)
  • Shelf Life: 1 Year
  • Shore D Hardness: 77 - 80 (ASTM D-2240)
  • Chemical Resistance: Sulfuric Acid, 98%: Very good Sulfuric Acid 70%: Excellent Hydrochloric Acid, 36%: Excellent Acetic Acid, up to 50%: Very good Sodium Hydroxide: Excellent Xylene: Excellent Gasoline: Excellent
    ESTIMATION CHART

    COVERAGE FOR COATING OR MEMBRANES
    Thickness of Coating Applied
    (1000 mils = 1 inch)    		 Coverage per U.S. Gallon
    100% Solids System
    1/4 inch = 250 mils 6.4 Square Feet
    3/16 inch = 187.5 8.5 Square Feet
    1/8 inch = 125mills 12.8 Square Feet
    100mils 16.0 Square Feet
    1/16 inch = 62.5 mils 25.5 Square Feet
    50 mils 32.0 Square Feet
    1/32 inch = 31.25 mils 51.0 Square Feet
    20 mils 80.0 Square Feet
    1/64 inch = 15.625 mils 102.0 Square Feet
    10 mils 160.0 Square Feet
    5 mils 320.0 Square Feet
    1 mil 1600.0 Square Feet
    If coating contains a solvent which will evaporate, thickness of coating will be reduced by same percentage as solvent loss.


Request Information
 

 

Superior Epoxies & Coatings, Inc. (800) 240-1310
Fax: (800) 240-7662
2527 Lantrac Court
Decatur GA 30035
© 2006 Superior Epoxies & Coatings. All Rights Reserved   
Web Design by SMF Associates